| | |  | Broadcaster Products | Home » » Cables to Go 37133 2-Port RJ45 Splitter/Combiner Cable, Gray 6-Inch (Single Unit*) | | | | | | | Description: | | This 2-port passive splitter is handy when you need another network connection but don't have the time or the money to add another cable drop. Simply plug one device into your work area network port and another unit to the corresponding patch panel port. Now you can run two network devices over the same network cable. Non-intrusive to the network; a simple plug-and-play installation. Please Note: Sold individually, this item must be used in pairs for each installation, one on each end of the cable. | | | Features: | |
• * Note: Sold individually, this item must be used in pairs for each installation, one on each end of the cable
• This 2-port passive splitter is handy when you need another network connection but don't have the time or the money to add another cable drop
• Simply plug one device into your work area network port and another unit to the corresponding patch panel port. Plug and play operation. Supports network speeds up to 100 Mbps
• Non-intrusive to the network
• Lietime warranty
| | | Product Details: | | | Product Length:
| 5.2 inches | | Product Width:
| 3.5 inches | | Product Height:
| 1.1 inches | | Product Weight:
| 0.05 pounds | | Package Length:
| 6.2 inches | | Package Width:
| 2.6 inches | | Package Height:
| 0.5 inches | | Package Weight:
| 0.05 pounds | | Average Customer Rating:
|  based on 100 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 100 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
238 of 242 found the following review helpful:
 Works perfectlyMay 19, 2009
By Bruce
I'm thinking the people rating this poorly don't understand how to use it. It WON'T split a single Ethernet CONNECTION into two. It WILL enable a single Ethernet CABLE (which has 8 wires) to carry two connections (which require 4 wires each). This is helpful in places where you have a single cable running from your router (typically in a wiring closet) to two devices, and can't easily run a second cable -- i.e., where one cable is already installed in the walls.
Here's how you use it: Run Ethernet cables from 2 ports of your router into the female jacks of the first splitter. Plug the male end of that splitter into the jack in your wiring closet that runs to the part of your house you want. Plug the male end of the second splitter into the Ethernet jack at the other end of that cable run (i.e., in the room where the devices are located). Run Ethernet cables from the female jacks of the second splitter to the devices.
If you want to use a single Ethernet connection for two devices, these splitters won't work; you need a router that shares the connection among the devices.
22 of 23 found the following review helpful:
This Item is for System Administrators ONLYMay 21, 2010
By S. Ellis
"IT-Pro"
This item is for System Administrators/I.T. Professionals ONLY. If you don't know what this item is for, it is not for you.
This item is NOT a HUB or SWITCH. It allows a standard ethernet with 4 pairs (eight wires) to be split into 2 sets of 2 pair (4 wires + 4 wires) so that you can have ethernet devices through 1 ethernet cable.
To use this item, you need 2 splitting the wire on both ends of the cable.
I am using this very successfully with a computer @ 100Mbits full and a VOIP/IP Phone @ 100Mbits full with POE on 2 different networks.
109 of 130 found the following review helpful:
 Do you know how this works?Aug 08, 2008
By Stephen E. Jones
"Steve Jones"
I dont own this item, but I'm thinking of buying some, then I saw the bad reviews..
From reading the reviews, it seems, at least from the first one, that the person didn't know how to use the item.. This is NOT a 3 port switch. You can NOT plug the male plug into a switch and have it run two PCs... It is splitting the 4 pairs (8 wires) into TWO separate two-pair outlets.
Ethernet only uses pins 1, 2, 3, and 6, leaving 4, 5, 7, and 8 unused. This device connects pins 1, 2, 3, and 6 on the male to 1, 2, 3, and 6 on one of the femals jacks, and pins 4, 5,7, and 8 of the male go to pins 1, 2, 3, and 6 of the OTHER female, giving you two separate paths of pins 1, 2, 3 and 6.
The idea is that if you need two PCs where you only have one jack in the wall, you plug one of these into the jack, and another one into the patch panel, and it allows you to hook two PCs to two separate switch ports. You will STILL need 2 separate switch ports to connect your two PCs, and you will ALWAYS need these splitters in pairs because you'll need to have one on each end of your 4-pair house cable.
Now.. Does this make sense? And, given this description, are any of the negative reviews still valid? I dont want to buy a piece of junk, but as this is not even an active device, but rather just like a wiring adapter, I can't imagine that it could fail, short of it being a physically poorly constructed device...
11 of 11 found the following review helpful:
Perfect!Jul 23, 2010
By P. Smith
I used two of these to split a cable run into two separate connections. worked great. you need two of these, one on each end of the run, to complete this setup. Think of it as a two lane onramp into a tunnel, with an identical two lane offramp at the other end of the tunnel. the traffic on the two lanes never mixes, not even in the "tunnel".
9 of 9 found the following review helpful:
Very good product, if you know how to use itOct 05, 2009
By Mark Twain
"wwwumax"
This is a passive device. This is not a switch. This requires a switch to work with. This need to use in pairs. This splitter assume in Ethernet and Fast Ethernet case only 4 out of 8 wires are used. Assume you have one Cat 6 routed in the wall, and you want to hook up 2 devices from the outlet. One way is to link up a switch and split actively at local desk. Another way is to link two devices to this product and plug in your wall outlet. At the other side where the single line goes to switch or router, you need to add another such splitter reversely and the two outputs connect to "two" switch ports. That way, you are sharing one line of two devices with one less router.
The down side is the additional length from computer/device to switch, which in fact regenerate the signal. I doubt this splitter will have less driving distance.
Another down side is that it can't support Giga-bit Ethernet where 8 lines are used.
So, if you want to go green and save the always on switch, use it! I hate wireless, hence I wired my whole house with many switches. I've bought 4 of such splitter to save 2 more switches.
See all 100 customer reviews on Amazon.com
| | |
|
